[Mach40]

I have a 09 Pro 4 x with a 3" PRG lift I am looking to put a set of 20" KMC rockstars with 33x12 Nitto tera grapplers but I am not sure of the correct back spacing any help would be much apreciated. thanks!

 

[zluke13]

I like the Rockstars but I've heard they chip really easily. One guy said you can't mount tires on them without taking some coating off. I don't have personal experience, but for the $$$ you're going to spend you may want to look into it a bit.

 

[Mach40]

Now you are the second person to tell me that. Do you have any wheel recomendations ? I was also looking at the motometal wheels but I would really like a flat black wheel

 

[Irongrave]

FYI moto metal and KMC is the same company they are owned by Wheel Pros. I'd look at some of the other KMC wheels the monsters and addicts are nicer IMO then the rock starts

 

[Mach40]

Kmc

I like the monsters too but I am woried about them chipping, I plan on using a 33x 12 on a 20 x 10 wheel so with the large section width of the tire should over hang the wheel a good 1.5 inches on both sides to help from geting chipped or scratched . But I still don't know what is the proper offset I talked to a guy that works for Fabtech and he told me I should use a wheel with a 5" backspacing.

FYI moto metal and KMC is the same company they are owned by Wheel Pros. I'd look at some of the other KMC wheels the monsters and addicts are nicer IMO then the rock starts

 

[zluke13]

Take a look at American Outlaw. I like some of theirs too.

American Outlaw Wheel

 

[Mach40]

I checked them out too but I still like the monsters and rockstars

 

[00 FRONTIER]

Its all personal preference, but I would leave the Rockstars to the fullsize rigs, especially 20's. My buddy was talking about them for his taco and I gave him my $.02. I am sure everyone has heard of "donk"... Yea, kinda reminds me of that.

http://img.photobucket.com/albums/v429/soultron/DONK.jpg

Also, from my understanding they dont bolt up either, you have to run a wheel adapter.

There is a member on here that runs KMC Addicts (I think) and I believe they bolted right up. His are silver and black, but they also make an all black.

 

[domoMKIV]

There is a member on here that runs KMC Addicts (I think) and I believe they bolted right up. His are silver and black, but they also make an all black.

Yes they bolt right up, I have them on my truck.


I think the rockstars would look OK with the right tire and lift setup, but you will need adapters to run them.

 

[Mach40]

How much lift does your truck have and what size wheel and tire did you buy? what was the backspacing?

 

[Mach40]

I know motometal whels bolt right up but I want to go big I am thinking 20 x 9.5 but How much backspacing would I need? gonna use a 33x 12 tire

that looks great

 

[domoMKIV]

I just found those on a Tacoma forum, posted them up for size reference as I mostly see rockstars on fullsize trucks.

 

[foxxracer278]

i wish rockstars would just bolt on they are so so nice that will be my next rim by far i love them

 

[Mach40]

They look better on our trucks though LOL

A KMC rep told me you can order a set with a blank bolt patern and have them drilled to fit. they come 5 on 4.5 so why not 6 on 4.5

 

[00 FRONTIER]

they come 5 on 4.5 so why not 6 on 4.5

Because 5x4.5 (Ranger, Jeep, etc) is more common than our 6x4.5 (Us and Durango/Dakota I think). Its probably not cost effective to set up the equipment and and pre drill our bolt pattern for the minimal amount of orders they will get.

I am sure Nissan had a very good reason for setting up our trucks with this bolt pattern , but I have yet to figure it out.

 

[Mach40]

Does anybody know if a 305 65 17 will fit on the stock wheel without rubbing on a fronty with a 3' PRG lift?

 

[Mach40]

This is insane I really can't find a nice 20" wheel that will fit this truck wtf!!