Nissan Frontier Forum banner

Search results

1-20 of 191 Results
Advanced Search
  1. Anyone with a King cab 03-04. Short bed 2WD

    1st Gen Hangout
    Thank you again.
  2. Anyone with a King cab 03-04. Short bed 2WD

    1st Gen Hangout
    Soo. Would you be able to take a shot and measure the rear also? Thanks a bunch.
  3. Anyone with a King cab 03-04. Short bed 2WD

    1st Gen Hangout
    Thank you. I'm pretty my bed length is the same. Those measurements sounds right. I will check tonight though. I appreciate it.
  4. Anyone with a King cab 03-04. Short bed 2WD

    1st Gen Hangout
    Well this makes me sad. No one has a 2wd king cab that can help me out?
  5. 2003 rear axle interchangeability vs. gear swap

    1st Gen Hangout
    I can look into the cost if you want
  6. 2003 rear axle interchangeability vs. gear swap

    1st Gen Hangout
    I have an 04 Desert Runner with the same gears. The perches are underneath the axle. It does have a sensor at the front of the housing. I would ship you the ring and pinion if you wanted to pay for it. Probably cost a pretty penny coming from FL.
  7. Request: Long Term Review of Dirt King Long Travel and similar setups

    OffRoad / 4x4
    I ran the Total Chaos Fab kit on my first gen for a while. Had no real issues. Would put zerk fitting on the joints if it was me.
  8. Anyone with a King cab 03-04. Short bed 2WD

    1st Gen Hangout
    So I'm an idiot. I'm doing a transformation Tuesday on my truck and before removing the rear axle and leaf springs I forgot to mark on the frame where the axle is positioned in relation to the frame. If someone could do me a solid with the above truck and measure say from the front leaf eye...
  9. Long Travel front suspension, 1st Gen

    Parts
    Yes of course
  10. Long Travel front suspension, 1st Gen

    Parts
    I am selling my Total Chaos long travel front suspension. I have it on my 04 Frontier. It should fit 01-04 Frontiers that are 2wd. I dont know about the Xterras. Maybe 02-04. I will be including upper and lower control arms, spindles, center link, tie rods, Pittman arm, idler arm and brace, Sway...
  11. Vg33 turbo build

    1st Gen Frontier Builds
    Pistons and wrist pins I got from J.E. They had to make them. Most reasonably priced. The rings I got from Nissan.I am 99% sure the rods are forged from what I have seen and people have said.
  12. Vg33 turbo build

    1st Gen Frontier Builds
    Everything was good. It ran like a champ except I kept blowing out the valve cover gaskets. That's why I did the compression check. 35 on cyl 1 and 65 on cyl 2. I thought it was rings until I pulled the piston out.
  13. Vg33 turbo build

    1st Gen Frontier Builds
    It is not the rings my friend. You have exceeded the torque specification for the ring to ring land pressure. I tried to make that sound smart but with 30 psi of compression I pulled the piston out and the ring lands fell out into my hand. I hope its just the rings for your sake. I can only...
  14. Vg33 turbo build

    1st Gen Frontier Builds
    I'm glad to hear that everything is running properly. I am shocked that those head gaskets haven't changed over the years. A short pipe might make a pretty big difference. Mine is internal so I was never worried about it. How did you end up wiring the O2 sensors in? I am curious to see your...
  15. Vg33 turbo build

    1st Gen Frontier Builds
    Not in voltage mode. You are literally telling the computer the voltage the MAF is sending in. Not changing a percentage of the value coming in. Where 0 would be no change. Since you are entering the voltage it will read as 0. When I get home tonight I will look at my MAF graph and let you...
  16. Vg33 turbo build

    1st Gen Frontier Builds
    I PM'd you. My head gaskets blew in the same spot. GO to settings and on the left where it says MAF change it from settings to percent. Or did you mean you did that and it stalled? Are the numbers all at 0? If so then yes it will stall.
  17. Vg33 turbo build

    1st Gen Frontier Builds
    Those composite head gasket aren't meant to run a lot of boost. I blew out both of mine running over 10 psi. I dont have the picture any more but there are 6 passages along each bank, 2 by each cylinder. It sounds like they are gone. I wasn't able to find MLS head gaskets anywhere so I had a...
  18. Vg33 turbo build

    1st Gen Frontier Builds
    Yes intercept the purple wire before it splits in two. I will double check but I had issues with the green wire. I think the truck wouldn't start. Putting a component in series is the same as intercepting it like AEM instructions show. You are wiring it in line. You need to put it in series so...
  19. 04 King cab for sale.

    Vehicles
    Turbo 04 King cab for sale. 9k OBO. Build thread with info in link. PM or post for info. http://www.clubfrontier.org/forums/f102/handb94-s-2004-desert-runner-87570/#post1191465
1-20 of 191 Results
Top